This pad builds on [[hacklab-osalistat/rev.2384]], created by Hukka & jari & Teemu & Jssmk & Kilpuri & suovula & hacklab-ole & daned33 & Tesla & jautero & rambo & creepy & ApaVe & tkln & Eipou & PullaEmu & Psoden & dah & Harri & kengu & Yleinen & Labin olohuone & anacron & zzorn & Mike & jimki & lapm & Kremmen & Miksi_ & Creepy & [unnamed author] & Jammi & LabinEleKone & Heikki & vesa & kenkku & jssmk & rostb & dist
Lainataan (L) / myydään (M) / annetaan hyvään kotiin (A) osia
Can lend (L) / sell (M) / give for good purpose (A) parts
Helsingin läbin ns ylijäämälista: http://kirjoitusalusta.fi/hacklab-ylijaama
XMegoja (suovula): https://kirjoitusalusta.fi/hacklab-x-xmega
qriff (2014-10-04)
*(A) iRobot Roomba 500
*Fully working condition, including all accessories.
Hukka (päivitetty 2011-10-12)
*Parts are in Espoo, ask in IRC
*(L/M 4€) couple TI MSP430 Launchpads
*(L) Arduino Mega 2560
*(L) 10mmx2mm disc vibrators <http://www.pololu.com/catalog/product/1638>
*(L) 3d accelometer+compass <LSM303DLH, http://www.pololu.com/catalog/product/1250>
*(A/M) basic components for sudden need
zzorn (updated 2011-11-12)
*Parts at lab, ask in person at lab or on IRC
*(M) Selling RGB Led strip, 60 leds / meter, 12V, common anode, adhesive back
*10€ / meter
rambo (2014-02-03)
*Various parts @lab or @kirkkonummi, ask me. I also have @kirkkonummi small vertical mill (yläjyrsin), lathe (sorvi) and bandsaw (vannesaha) for metalworking with soft metals and 60A plasma cutter that should go through 10mm steel (now @stadi mallarit)
*(M) Neurosky dry-sensor EEG ASIC on breakout board (aka TGAM), 57600 serial com, handles FFT etc inside the ASIC (4 pcs left), 37EUR/ea
*(M/A) I2C Level shifters (can't remember the exact model offhand), if you have 1.8V parts you want to interface with 5V microcontroller like Arduino you will need one of these. ~1EUR /ea
*(A) breakout boards for two different kinds of SD-card slot/holder/thingy, I'll check the models when I remember. Note only the boards, you need to source the thingy yourself (got mine from RS)
*(A) breakout/led adapter -boards for 4 SMD 595 shift-registers, again board only. There is a bunch of those SMD 595s @lab.
*(A/M) ATTIny85 and ATMega168 SMD bare chips, we have couple of AVRISPs at the lab you can use to flash them
*(A) ATTiny85/45/25 SMD breakout boards https://github.com/rambo/attiny_boards a bunch of boards from two first revisions (have minor silkscreen bugs and the earliest revision has no provision for xtal [not that you're likely even want it])
*As explained on the linked page, the SMD parts are a lot cheaper than DIP ones, size is a consideration too...
suovula (2012-07-23)
*Parts at lab, ask on IRC
*(L) AVRISP mkII <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3808>
*(L) Xminilab scope for ATXmega development <http://www.gabotronics.com/development-boards/xmega-xminilab.htm>
*(L) Hall-sensors: switches, linears and rotary-encoders, ask for more details
*(L) small stepper motors <http://www.pololu.com/catalog/product/1204>
kimka (updated 2012-05-16)
email: before writing @nic.fi, add kimka.
*(M) Portable air conditioner (the one at Hacklab) - 190 euros/make offer
*(M) Lego Mindstorms NXT 2.0 (LEGO 8547), mint conditon, used twice - 220 euros/make offer
*(M) Thinkpad X40 "minilaptop", 1.2GHz Pentium M, 12" 1024x768, 40GB HD, 1GB RAM, B/G wlan. Battery lasts about one hour of normal use.- 100 euros (specs: http://www.thinkwiki.org/wiki/Category:X40 )
PullaEmu (2012-10-2)
*@lab
*(L/M) STM32F0Discovery (10e)
*(L/M) STM32F4Discovery (20e)
*@Munkkivuori
*(L/M) DS1307 RTC w/eeprom (5e)
*(A) Basic components (E12 through hole / 0805 resistors, few opamps, BJTs etc)
jimki (2013-01-28)
*(M) 17" 4:3 4-wire touch screen glass with USB controller (45e)