This pad builds on [[hacklab-osalistat/rev.2384]], created by Hukka & jari & Teemu & Jssmk & Kilpuri & suovula & hacklab-ole & daned33 & Tesla & jautero & rambo & creepy & ApaVe & tkln & Eipou & PullaEmu & Psoden & dah & Harri & kengu & Yleinen & Labin olohuone & anacron & zzorn & Mike & jimki & lapm & Kremmen & Miksi_ & Creepy & [unnamed author] & Jammi & LabinEleKone & Heikki & vesa & kenkku & jssmk & rostb & dist Lainataan (L) / myydään (M) / annetaan hyvään kotiin (A) osia Can lend (L) / sell (M) / give for good purpose (A) parts Helsingin läbin ns ylijäämälista: http://kirjoitusalusta.fi/hacklab-ylijaama XMegoja (suovula): https://kirjoitusalusta.fi/hacklab-x-xmega qriff (2014-10-04) *(A) iRobot Roomba 500 *Fully working condition, including all accessories. Hukka (päivitetty 2011-10-12) *Parts are in Espoo, ask in IRC *(L/M 4€) couple TI MSP430 Launchpads *(L) Arduino Mega 2560 *(L) 10mmx2mm disc vibrators *(L) 3d accelometer+compass *(A/M) basic components for sudden need zzorn (updated 2011-11-12) *Parts at lab, ask in person at lab or on IRC *(M) Selling RGB Led strip, 60 leds / meter, 12V, common anode, adhesive back *10€ / meter rambo (2014-02-03) *Various parts @lab or @kirkkonummi, ask me. I also have @kirkkonummi small vertical mill (yläjyrsin), lathe (sorvi) and bandsaw (vannesaha) for metalworking with soft metals and 60A plasma cutter that should go through 10mm steel (now @stadi mallarit) *(M) Neurosky dry-sensor EEG ASIC on breakout board (aka TGAM), 57600 serial com, handles FFT etc inside the ASIC (4 pcs left), 37EUR/ea *(M/A) I2C Level shifters (can't remember the exact model offhand), if you have 1.8V parts you want to interface with 5V microcontroller like Arduino you will need one of these. ~1EUR /ea *(A) breakout boards for two different kinds of SD-card slot/holder/thingy, I'll check the models when I remember. Note only the boards, you need to source the thingy yourself (got mine from RS) *(A) breakout/led adapter -boards for 4 SMD 595 shift-registers, again board only. There is a bunch of those SMD 595s @lab. *(A/M) ATTIny85 and ATMega168 SMD bare chips, we have couple of AVRISPs at the lab you can use to flash them *(A) ATTiny85/45/25 SMD breakout boards https://github.com/rambo/attiny_boards a bunch of boards from two first revisions (have minor silkscreen bugs and the earliest revision has no provision for xtal [not that you're likely even want it]) *As explained on the linked page, the SMD parts are a lot cheaper than DIP ones, size is a consideration too... suovula (2012-07-23) *Parts at lab, ask on IRC *(L) AVRISP mkII *(L) Xminilab scope for ATXmega development *(L) Hall-sensors: switches, linears and rotary-encoders, ask for more details *(L) small stepper motors kimka (updated 2012-05-16) email: before writing @nic.fi, add kimka. *(M) Portable air conditioner (the one at Hacklab) - 190 euros/make offer *(M) Lego Mindstorms NXT 2.0 (LEGO 8547), mint conditon, used twice - 220 euros/make offer *(M) Thinkpad X40 "minilaptop", 1.2GHz Pentium M, 12" 1024x768, 40GB HD, 1GB RAM, B/G wlan. Battery lasts about one hour of normal use.- 100 euros (specs: http://www.thinkwiki.org/wiki/Category:X40 ) PullaEmu (2012-10-2) *@lab *(L/M) STM32F0Discovery (10e) *(L/M) STM32F4Discovery (20e) *@Munkkivuori *(L/M) DS1307 RTC w/eeprom (5e) *(A) Basic components (E12 through hole / 0805 resistors, few opamps, BJTs etc) jimki (2013-01-28) *(M) 17" 4:3 4-wire touch screen glass with USB controller (45e)